UPDATED 17 NOVEMBER 2026

TDS versus water hardness: why ppm is not enough

“My meter says 180 ppm; which dishwasher setting should I use?” The missing detail is what the meter measures. Ppm is a unit, not the name of a substance or test. Before converting it, identify whether the number represents total hardness or total dissolved solids.

Two different questions

USGS describes hardness primarily in terms of dissolved calcium and magnesium. Total dissolved solids describes a broader collection of dissolved material. The USGS groundwater-quality overview lists dissolved constituents including sodium, calcium, magnesium, chloride and sulfate. The broader total does not tell you how much belongs to the hardness-causing portion.

Why a conversion factor cannot solve it

Converting 180 mg/L of hardness as CaCO₃ to German degrees keeps the measurement the same and changes the unit: 180 ÷ 17.848 is about 10.09 °dH. Applying that arithmetic to 180 ppm TDS changes the meaning of the input. The resulting number may look plausible, but it is not a justified hardness result.

Think of a shopping bag with a known total weight. Its total cannot tell you the weight of the apples without knowing what else is inside. A more precise measurement of the whole bag still cannot supply that missing breakdown. Likewise, recording more decimal places from a meter does not identify the constituents of the water.

A practical decision sequence

  1. Read the device or report’s parameter label. Does it explicitly say total hardness?
  2. Check the unit and whether hardness is expressed as CaCO₃.
  3. If the reading is TDS, retain it as TDS. Obtain a separate hardness result from the supplier or a total-hardness test.
  4. Convert the hardness result into the unit in your exact appliance manual.

If a product advertisement only says “water quality tester”, read its specifications before buying or using it for an appliance setting. Ask the manufacturer which parameter the device reports. A label on the display is not evidence that it measures every property of water relevant to cleaning or brewing.

Read a label as a complete statement

Similar-looking readings with different meanings
LabelCan it be entered as ppm hardness?Next step
Total hardness: 180 mg/L as CaCO₃YesEnter 180, retaining its range and scope
Total hardness: 10 °dHAfter conversionMultiply by 17.848
TDS: 180 ppmNoObtain total hardness separately
Alkalinity: 80 mg/L as CaCO₃NoRetain it as an alkalinity result
Conductivity: a value in µS/cmNoDo not treat it as a mass concentration

“As CaCO₃” is a reporting basis, not proof that two tests measure the same property. Hardness and alkalinity can both use it. The USGS alkalinity explanation describes acid-neutralising capacity, which is different from hardness. For coffee, keeping those values separate helps avoid confusing extraction questions with buffering questions.

Why softening does not mean removing everything

USGS explains that household ion-exchange softening can replace calcium and magnesium with sodium in its water-quality FAQ. That is a change in composition, not a claim that all dissolved material has disappeared. It follows that a low-hardness result does not require a near-zero TDS result. The two tests can be answering their own questions correctly.

Consider a deliberately simplified before-and-after record: your hardness test changes substantially after treatment, while the separate TDS reading remains broadly similar. That pattern is not sufficient evidence that the hardness test failed. Conversely, a change in TDS does not demonstrate that the treatment achieved the hardness target. Evaluate the treatment using the parameter it is intended to change.

Three common mistakes to avoid

  1. Using a universal “TDS to hardness” percentage. A factor derived for one water composition cannot identify the composition of another. Ask what evidence supports the factor for your actual supply.
  2. Reading the display without the mode. Record the device model, selected parameter and unit together. A bare number copied into a note loses the information needed to interpret it.
  3. Calling a low number “pure” or “safe”. Neither hardness nor a single dissolved-solids reading is a complete test for contaminants. Use the relevant utility information and appropriate testing for the specific question.

A useful troubleshooting conversation

If appliance support asks for hardness and you have only a meter result, say exactly that: “My device reports TDS in ppm; I have not measured total hardness.” This prevents a precise-looking but unsuitable input from being used to select a setting. Supply a utility hardness result or a suitable home-test result when it becomes available.

Likewise, when comparing bottled water labels or filter claims, write the parameters in separate columns. A missing calcium, magnesium, hardness or alkalinity value stays missing; it cannot be filled in from the total alone. The practical benefit of this distinction is fewer unnecessary setting changes and a clearer idea of what information to obtain next.

What to enter in Waterdial

The manual field accepts total hardness in ppm, used here as mg/L as CaCO₃. If your report gives 12 °dH total hardness, multiply by 17.848 and enter approximately 214.18. If your only result is 214 ppm TDS, leave it out of the hardness converter and obtain the missing measurement first.

Keep the original parameter and units alongside any converted value. This makes it much easier to compare reports, repeat a home test and discuss a setting with appliance support. Our home-testing guide explains how to record a useful hardness result.

Explore all water and appliance guides · About our editorial approach · Suggest a correction